Post by yankymodeler on Jun 21, 2014 9:26:02 GMT -5
To start off, here RFI post I wrote a number of years ago I hope y'all don't mind a few re-posts from the past as I get a few new projects finished up.
Built a few years ago, this was my second model after a decade long break in modeling.
Started with the best of intentions to be a straight forward OOB build, the urge to add a few extra details began as I realized how well the rather basic kit captured the shape of the Hellcat. The discovery of an aftermarket resin cockpit and a vacuformed canopy in my stash :yahoo: began the construction. The kit has the lower cowl flaps of an early F6F-3 and with the addition of the fairings on the guns, one of the very early F6F-3s could be built. The gun fairings were fabricated from styrene. Only the first 273 Hellcats produced had these fairings and they were eventually removed in service.
The resin cockpit was modified to fit the Otaki kit. I had to fabricate the instrument panel not only because I broke the resin panel, but this allowed me to better replicate the early cockpit layout. :doh: A scratch built gun sight and trim tab control console were fabricated and installed. The vacuformed windshield needed a lot of trimming and filling to fit properly but is a great improvement to the very thick kit pieces. Armored glass was made from thicker clear plastic and set inside the windshield.
The wheel wells were too shallow caused by the well being a "box" attached to the bottom part of the wing. The wells were deepened by removing the top of the kit’s wheel well “box” from the lower wing pieces and a simple internal structure was added to underside of top wing surface.
Thanks for looking!
Eric aka The Yankymodeler
Thanks for looking!
Eric aka The Yankymodeler
The landing gear was detailed with various small linkages, the braces on the sides of the struts added with styrene strips. Brake lines were made from wire and the kit doors thinned by filing and sanding. Catapult bridle hooks were made from wire and added just inboard of the main gear. Exhaust pipes were fabricated from styrene rod drilled out, and glued inside the outlets in the bottom and sides of the cowling.
The rudder was too thick and was thinned by sanding. The fabric detail restored (though hard to see in the pics) by sanding with a rolled up piece of 400 grit to simulate the sag between the ribs and the rib tapes by a stripe of paint under the finish coats. The elevators and trim tabs were repositioned for a more natural look . (Yes, the control stick is in the nose down position!) A retracted tail hook and holdback bar were added.
The model is finished as the aircraft would have appeared while undergoing carrier qualifications aboard one of the early Essex class carriers working up off the west coast of the United States in the early summer of 1943, The paint is in good condition, the semigloss gone from the upper surfaces but not much fading is evident yet, while the undersides retain a bit of sheen. There is just a little exhaust staining and slight wear on the wing roots. With just a little bit of work, the Otaki/Arii kit can be made into a good representation of the Hellcat.
Thanks for looking!
Eric aka The Yankymodeler
Built a few years ago, this was my second model after a decade long break in modeling.
Started with the best of intentions to be a straight forward OOB build, the urge to add a few extra details began as I realized how well the rather basic kit captured the shape of the Hellcat. The discovery of an aftermarket resin cockpit and a vacuformed canopy in my stash :yahoo: began the construction. The kit has the lower cowl flaps of an early F6F-3 and with the addition of the fairings on the guns, one of the very early F6F-3s could be built. The gun fairings were fabricated from styrene. Only the first 273 Hellcats produced had these fairings and they were eventually removed in service.
The resin cockpit was modified to fit the Otaki kit. I had to fabricate the instrument panel not only because I broke the resin panel, but this allowed me to better replicate the early cockpit layout. :doh: A scratch built gun sight and trim tab control console were fabricated and installed. The vacuformed windshield needed a lot of trimming and filling to fit properly but is a great improvement to the very thick kit pieces. Armored glass was made from thicker clear plastic and set inside the windshield.
The wheel wells were too shallow caused by the well being a "box" attached to the bottom part of the wing. The wells were deepened by removing the top of the kit’s wheel well “box” from the lower wing pieces and a simple internal structure was added to underside of top wing surface.
Thanks for looking!
Eric aka The Yankymodeler
Thanks for looking!
Eric aka The Yankymodeler
The landing gear was detailed with various small linkages, the braces on the sides of the struts added with styrene strips. Brake lines were made from wire and the kit doors thinned by filing and sanding. Catapult bridle hooks were made from wire and added just inboard of the main gear. Exhaust pipes were fabricated from styrene rod drilled out, and glued inside the outlets in the bottom and sides of the cowling.
The rudder was too thick and was thinned by sanding. The fabric detail restored (though hard to see in the pics) by sanding with a rolled up piece of 400 grit to simulate the sag between the ribs and the rib tapes by a stripe of paint under the finish coats. The elevators and trim tabs were repositioned for a more natural look . (Yes, the control stick is in the nose down position!) A retracted tail hook and holdback bar were added.
The model is finished as the aircraft would have appeared while undergoing carrier qualifications aboard one of the early Essex class carriers working up off the west coast of the United States in the early summer of 1943, The paint is in good condition, the semigloss gone from the upper surfaces but not much fading is evident yet, while the undersides retain a bit of sheen. There is just a little exhaust staining and slight wear on the wing roots. With just a little bit of work, the Otaki/Arii kit can be made into a good representation of the Hellcat.
Thanks for looking!
Eric aka The Yankymodeler